#
# /usr/local/etc/postfix/main.cf
# Postfix main configuration file, see postconf(5) for details.
#
# For best results, change no more than 2-3 parameters at a time,
# and test if Postfix still works after every change.
#
# References
# ----------
# * Postfix Configuration Parameters
#   http://www.postfix.org/postconf.5.html
# * Postfix SASL Howto
#   http://www.postfix.org/SASL_README.html
# * Postfix Virtual Domain Hosting Howto
#   http://www.postfix.org/VIRTUAL_README.html
#
#
# Aaron LI
# 2017-04-15
#

{% set mydomain = mail.domains[0] %}

# COMPATIBILITY
#
# The compatibility_level determines what default settings Postfix
# will use for main.cf and master.cf settings. These defaults will
# change over time.
#
# To avoid breaking things, Postfix will use backwards-compatible
# default settings and log where it uses those old backwards-compatible
# default settings, until the system administrator has determined
# if any backwards-compatible default settings need to be made
# permanent in "main.cf" or "master.cf".
#
# When this review is complete, update the compatibility_level setting
# below as recommended in the RELEASE_NOTES file.
#
compatibility_level = 2

# SOFT BOUNCE
#
# The soft_bounce parameter provides a limited safety net for
# testing.  When soft_bounce is enabled, mail will remain queued that
# would otherwise bounce. This parameter disables locally-generated
# bounces, and prevents the SMTP server from rejecting mail permanently
# (by changing 5xx replies into 4xx replies). However, soft_bounce
# is no cure for address rewriting mistakes or mail routing mistakes.
#
#soft_bounce = no

# INTERNET HOST AND DOMAIN NAMES
# 
# The myhostname parameter specifies the internet hostname of this
# mail system.  The default is to use the fully-qualified domain name
# from gethostname().  $myhostname is used as a default value for many
# other configuration parameters.
#
myhostname = mail.{{ mydomain }}

# The mydomain parameter specifies the local internet domain name.
# The default is to use $myhostname minus the first component.
# $mydomain is used as a default value for many other configuration
# parameters.
#
mydomain = {{ mydomain }}

# SENDING MAIL
# 
# The myorigin parameter specifies the domain that locally-posted
# mail appears to come from. The default is to append $myhostname,
# which is fine for small sites.  If you run a domain with multiple
# machines, you should (1) change this to $mydomain and (2) set up
# a domain-wide alias database that aliases each user to
# user@that.users.mailhost.
#
# For the sake of consistency between sender and recipient addresses,
# myorigin also specifies the default domain name that is appended
# to recipient addresses that have no @domain part.
#
myorigin = $mydomain

# SHOW SOFTWARE VERSION OR NOT
#
# The smtpd_banner parameter specifies the text that follows the 220
# code in the SMTP server's greeting banner.
#
# You MUST specify $myhostname at the start of the text.  That is an
# RFC requirement.  Postfix itself does not care.
#
# NOTE: Give out as little information as possible :-)
#
smtpd_banner = $myhostname ESMTP


##
## RECEIVING MAIL
##

# The inet_interfaces parameter specifies the network interface
# addresses that this mail system receives mail on.  By default,
# the software claims all active interfaces on the machine. The
# parameter also controls delivery of mail to user@[ip.address].
#
# See also the proxy_interfaces parameter, for network addresses that
# are forwarded to us via a proxy or network address translator.
#
# Note: you need to stop/start Postfix when this parameter changes.
#
inet_interfaces = all

# The Internet protocols Postfix will attempt to use when making or
# accepting connections.  'all' for both IPv4 and IPv6.
#
inet_protocols = all

# The mydestination parameter specifies the list of domains that this
# machine considers itself the final destination for.
#
# These domains are routed to the delivery agent specified with the
# local_transport parameter setting.  By default, that is the UNIX
# compatible delivery agent that lookups all recipients in /etc/passwd
# and /etc/aliases or their equivalent.
#
# The default is $myhostname + localhost.$mydomain + localhost.
# On a mail domain gateway, you should also include $mydomain.
#
# Do not specify the names of virtual domains - those domains are
# specified elsewhere (see VIRTUAL_README).
#
# Do not specify the names of domains that this machine is backup MX
# host for.  Specify those names via the relay_domains settings for
# the SMTP server, or use permit_mx_backup if you are lazy (see
# STANDARD_CONFIGURATION_README).
#
# The local machine is always the final destination for mail addressed
# to user@[the.net.work.address] of an interface that the mail system
# receives mail on (see the inet_interfaces parameter).
#
# Specify a list of host or domain names, /file/name or type:table
# patterns, separated by commas and/or whitespace.  A /file/name
# pattern is replaced by its contents; a type:table is matched when
# a name matches a lookup key (the right-hand side is ignored).
# Continue long lines by starting the next line with whitespace.
#
# NOTE: If the machine is a mail server for its entire domain, then
#       "$mydomain" must be listed as well.
# NOTE: In order to avoid mail delivery loops, you must list all
#       hostnames of the machine, including $myhostname, and
#       localhost.$mydomain
#
# WARNING: NEVER list "virtual_mailbox_domains" or "virtual_alias_domains"
#          names as "mydestination" domains here!
#          See also the below $virtual_mailbox_domains .
#
# NOTE: Since we will use the virtual(8) mailbox delivery agent (i.e.,
#       invoke "dovecot") for $mydomain, we should list $mydomain under
#       $virtual_mailbox_domains instead here!
#
mydestination = $myhostname, localhost.$mydomain, localhost


##
## TRUST AND RELAY CONTROL
##

# The mynetworks parameter specifies the list of "trusted" SMTP
# clients that have more privileges than "strangers".
#
# In particular, "trusted" SMTP clients are allowed to relay mail
# through Postfix.  See the 'smtpd_recipient_restrictions' parameter.
#
# You can specify the list of "trusted" network addresses by hand
# or you can let Postfix do it for you (which is the default).
#
# By default (mynetworks_style = subnet), Postfix "trusts" SMTP
# clients in the same IP subnetworks as the local machine.
# 
# Specify "mynetworks_style = class" when Postfix should "trust" SMTP
# clients in the same IP class A/B/C networks as the local machine.
# Don't do this with a dialup site - it would cause Postfix to "trust"
# your entire provider's network.  Instead, specify an explicit
# mynetworks list by hand, as described below.
#  
# Specify "mynetworks_style = host" when Postfix should "trust"
# only the local machine.
# 
mynetworks_style = host

# The relay_domains parameter restricts what destinations this system will
# relay mail to.  See the smtpd_recipient_restrictions description in
# postconf(5) for detailed information.
#
# By default, Postfix relays mail
# - from "trusted" clients (IP address matches $mynetworks) to any destination,
# - from "untrusted" clients to destinations that match $relay_domains or
#   subdomains thereof, except addresses with sender-specified routing.
# The default relay_domains value is $mydestination.
# 
# In addition to the above, the Postfix SMTP server by default accepts mail
# that Postfix is final destination for:
# - destinations that match $inet_interfaces or $proxy_interfaces,
# - destinations that match $mydestination
# - destinations that match $virtual_alias_domains,
# - destinations that match $virtual_mailbox_domains.
# These destinations do not need to be listed in $relay_domains.
# 
# Specify a list of hosts or domains, /file/name patterns or type:name
# lookup tables, separated by commas and/or whitespace.  Continue
# long lines by starting the next line with whitespace. A file name
# is replaced by its contents; a type:name table is matched when a
# (parent) domain appears as lookup key.
#
# NOTE: Postfix will not automatically forward mail for domains that
# list this system as their primary or backup MX host. See the
# permit_mx_backup restriction description in postconf(5).
#
#relay_domains = $mydestination


##
## Mail delivery for system users
##

# ALIAS DATABASE
#
# The alias_maps parameter specifies the list of alias databases used
# by the local delivery agent.  The default list is system dependent.
#
# If you change the alias database, run "postalias /etc/aliases"
# (or wherever your system stores the mail alias file), or simply run
# "newaliases" to build the necessary DBM or DB file.
#
alias_maps = hash:/etc/mail/aliases
#
# The alias_database parameter specifies the alias database(s) that
# are built with "newaliases" or "sendmail -bi".  This is a separate
# configuration parameter, because alias_maps (see above) may specify
# tables that are not necessarily all under control by Postfix.
#
alias_database = $alias_maps

# ADDRESS EXTENSIONS (e.g., user+foo)
#
# The recipient_delimiter parameter specifies the separator between
# user names and address extensions (user+foo). See canonical(5),
# local(8), relocated(5) and virtual(5) for the effects this has on
# aliases, canonical, virtual, relocated and .forward file lookups.
# Basically, the software tries user+foo and .forward+foo before
# trying user and .forward.
#
recipient_delimiter = +

# The mailbox_command parameter specifies the optional external
# command to use instead of mailbox delivery.  The command is run as
# the recipient with proper HOME, SHELL and LOGNAME environment settings.
# Exception: delivery for root is done as $default_user.
#
# Other environment variables of interest: USER (recipient username),
# EXTENSION (address extension), DOMAIN (domain part of address),
# and LOCAL (the address localpart).
#
# Unlike other Postfix configuration parameters, the mailbox_command
# parameter is not subjected to $parameter substitutions.  This is to
# make it easier to specify shell syntax.
#
# Avoid shell meta characters because they will force Postfix to run
# an expensive shell process.
#
# IF YOU USE THIS TO DELIVER MAIL SYSTEM-WIDE, YOU MUST SET UP AN
# ALIAS THAT FORWARDS MAIL FOR ROOT TO A REAL USER.
#
# See also: https://wiki.dovecot.org/LDA/Postfix
#
mailbox_command =
	/usr/local/libexec/dovecot/deliver
	-f "$SENDER" -a "$RECIPIENT"


##
## SASL authentication and authorization with Dovecot
##
## See: https://wiki2.dovecot.org/HowTo/PostfixAndDovecotSASL
##

# Use the Dovecot SASL implementation
smtpd_sasl_type = dovecot

# Path to the Dovecot authentication server.
# Here the path relative to the Postfix queue directory is used,
# so that it will work whether or not the Postfix SMTP server
# runs chrooted.
smtpd_sasl_path = private/auth

# Enable SASL authentication
smtpd_sasl_auth_enable = yes

# SMTP server policies on SASL mechanisms available to the clients.
#
# SASL mechanism properties:
#   - noanonymous     : don't use mechanisms that permit anonymous
#                       authentication (i.e., disable ANONYMOUS auth);
#   - noplaintext     : don't use mechanisms that transmit unencrypted
#                       username and password information
#                       (i.e., disable PLAIN auth);
#   - nodictionary    : don't use mechanisms that are vulnerable to
#                       dictionary attacks;
#   - forward_secrecy : require forward secrecy between sessions (breaking
#                       one session does not break earlier sessions);
#   - mutual_auth     : use only mechanisms that authenticate both the
#                       client and the server to each other.
#
# NOTE: Always set at least the 'noanonymous' option!
#       Otherwise, the Postfix SMTP server can give strangers the same
#       authorization as a properly-authenticated client!
#
# Allows plaintext mechanisms (e.g., PLAIN, LOGIN), but only over a
# TLS-encrypted connection:
smtpd_sasl_security_options = noanonymous, noplaintext
smtpd_sasl_tls_security_options = noanonymous

# Offer SASL authentication only after a TLS-encrypted session has
# been established.
smtpd_tls_auth_only = yes

# The name of the Postfix SMTP server's local SASL authentication realm,
# which tells Postfix append a domain name (or any other string) to a
# SASL login name that does not have a domain part (e.g., "username"
# instead of "username@example.com").
# This is useful as a default setting and safety net for misconfigured
# clients.
#smtpd_sasl_local_domain = $mydomain

# Report the SASL authenticated user name in "Received:" message headers.
# NOTE: The SASL login names will be shared with the entire world.
smtpd_sasl_authenticated_header = yes


##
## Access control & address verification
##

# By default, Postfix has a moderately restrictive approach to mail
# relaying.  See the "smtpd_relay_restrictions" parameter for a
# description of the default mail relay policy.
#
# References:
# * Postfix SMTP Relay and Access Control
#   http://www.postfix.org/SMTPD_ACCESS_README.html
# * Postfix Address Verficiation Howto
#   http://www.postfix.org/ADDRESS_VERIFICATION_README.html
# * CentOS Wiki - HowTos - Postfix Restrictions
#   https://wiki.centos.org/HowTos/postfix_restrictions
#

# Example SMTP session explaining the various restrictions/checks:
#+--------------------------------------------------------------------+
#| $ telnet <server> 25
#| <- 220 mail.example.com ESMTP Postfix        # smtpd_client_restrictions
#| -> HELO mail.example.com                     # smtpd_helo_restrictions
#| <- 250 mail.example.com
#| -> MAIL FROM:<sender@example.com>            # smtpd_sender_restrictions
#| <- 250 2.1.0 Ok
#| -> RCPT TO:<recipient@example.com>           # smtpd_recipient_restrictions
#| <- 250 2.1.5 Ok
#| -> DATA                                      # smtpd_data_restrictions
#| <- 354 End data with <CR><LF>.<CR><LF>
#| -> To:<recipient@example.com>                # header_checks
#| -> From:<sender@example.com>
#| -> Subject:SMTP test
#| -> This is a test meesage.                   # body_checks
#| -> .
#| <- 250 2.0.0 Ok: queued as xxxxxxxxxx
#| -> QUIT
#| <- 221 2.0.0 Bye
#+--------------------------------------------------------------------+

# NOTE:
# The HELO name is not related to and doesn't matter for
# 'reject_unknown_client_hostname'.  Note that there are two different
# context of hostname: client (rDNS) vs. HELO (SMTP).
# The *client* hostname is determined by an rDNS lookup of the connecting
# IP.  The resulting rDNS hostname is then looked up, and must resolve
# to the connecting IP.  This is also referred to as "Forward Confirmed
# reverse DNS" (FCrDNS).

# Wait until the "RCPT TO" or "ETRN" commands before evaluating the
# corresponding restriction rules. (default: yes)
#
# This allows Postfix to log recipient address information when rejecting
# a client name/address or sender address.
#
smtpd_delay_reject = yes

# Require that the client sends the HELO/EHLO command before sending
# the MAIL FROM or TERN command, i.e., senders must identify themselves
# before we'll accept e-mail commands from them.  This is important
# because we can use the way the remote server identities itself as a
# basis for accepting or rejecting mail from it --- spammers often
# don't issue proper HELO/EHLO response.
#
# NOTE: This may cause problems with home-grown clients, therefore,
#       this requirement is disabled by default.
#
smtpd_helo_required = yes
#
# Restrictions that the Postfix SMTP server applies in the context of
# a client HELO command.
#
# * reject_non_fqdn_helo_hostname : reject connections if the hostname
#       supplied with the HELO command is not a fully qualified domain
#       name as required by the RFC guidelines.
# * reject_invalid_helo_hostname : reject connection attempts when the
#       HELO hostname syntax is invalid.
# * reject_unknown_helo_hostname : reject messages if the hostname
#       supplied with the helo command doesn't have either a valid DNS
#       A or MX record.
#
# NOTE: set 'smtpd_helo_required=yes' to fully enforce this restriction.
#
# WARNING:
# Do note that the HELO/EHLO check that requires a valid hostname is
# going to drop legitimate mail.  Yes, people running mail servers
# should know better, but there are way to many Exchange servers out
# there that will spit out a HELO line like "localhost.localdomain"
# or "SERVER1.LOCAL" or other nonsense.  Therefore, maintaining a
# whitelist (which is a pain) may be necessary.  In addition, the
# rejections will show up in your logs, so it's possible to enable
# the check and then see who you're blocking.
#
# WARNING:
# The 'reject_unknown_helo_hostname' policy should be used with
# *caution* as it # will reject email from legitimate systems with
# temporary DNS problems and can lead to false positives.
#
smtpd_helo_restrictions =
	permit_mynetworks,
	check_helo_access pcre:$config_directory/helo-access.pcre,
	reject_non_fqdn_helo_hostname,
	reject_invalid_helo_hostname,
	warn_if_reject reject_unknown_helo_hostname,
	permit

# Relay control
# Only local clients and authenticated clients may specify any
# destination domain.
#
# WARNING: The 'reject_unauth_destination' is critically important!
#          The server would be an *open relay* without this!
#
smtpd_relay_restrictions =
	permit_mynetworks,
	permit_sasl_authenticated,
	reject_unauth_destination

# WARNING: Recipient address verficiation may cause an increased load
#          on down-stream servers in the case of a dictionary attack
#          or a flood of backscatter bounces.
#
smtpd_recipient_restrictions =
	reject_unknown_reverse_client_hostname,
	warn_if_reject reject_unknown_client_hostname,
	reject_non_fqdn_recipient,
	reject_unknown_sender_domain,
	reject_unknown_recipient_domain,
	permit_mynetworks,
	permit_sasl_authenticated,
	reject_invalid_hostname,
	reject_non_fqdn_sender

# Block clients that speak too early.
# Reject the request when the client sends SMTP commands ahead of
# time where it is not allowed, or when the client sends SMTP commands
# ahead of time without knowing that Postfix actually supports ESMTP
# command pipelining.
#
smtpd_data_restrictions = reject_unauth_pipelining

# Envelope sender address control
#
# * reject_unknown_sender_domain:
#       Don't accept mail from domains that don't exist.
# * reject_sender_login_mismatch:
#       Reject the sender address in the "MAIL FROM" command if
#       $smtpd_sender_login_maps does not specify the SMTP client's login
#       name (i.e., SASL authenticated) as an owner of that address. 
#
# WARNING: Sender address verficiation may cause your site to be
#          blacklisted by some providers.
#
# NOTE:
# By default an SMTP client may specify *any* envelope sender address
# in the "MAIL FROM" command, because the server only knows the remote
# client's hostname and IP address, but not the user who controls the
# remote client.
# But the Postfix SMTP server knowns who the sender is once the SASL
# authentication is used.  Given a table of envelope sender addresses
# and SASL login names ($smtpd_sender_login_maps), the server can
# decide if the SASL authenticated client is allowed to use a particular
# envelope sender address.
#
smtpd_sender_restrictions =
	reject_unknown_sender_domain,
	reject_sender_login_mismatch

# A lookup table maps between the envelope sender addresses and SASL
# login names (i.e., the owners).
#
smtpd_sender_login_maps = $virtual_mailbox_maps

# Use permanet 550 errors for rejections, to stop retries.
# Tell Postfix to reject messages that match the rejection criteria
# with a 550 error, which should tell the remote server that its
# message wasn't delivered and it shouldn't try to send it again
# (as opposed to the default 450 error, which implies that the
# remote server should retry sending).
#
#unknown_address_reject_code = 550
#unknown_client_reject_code = 550
#unknown_hostname_reject_code = 550


##
## SMTP server TLS settings
##

# Ask remote servers to identify themselves with a certificate.
#
smtpd_tls_ask_ccert = yes

# TLS certificate and key for this server (host)
#
smtpd_tls_cert_file = /usr/local/etc/ssl/acme/$mydomain/fullchain.pem
smtpd_tls_key_file = /usr/local/etc/ssl/acme/private/$mydomain.pem

# A CA bundle used by Postfix to validate remote servers' certificate.
# NOTE: install package 'ca_root_nss'.
#
smtpd_tls_CAfile = /usr/local/etc/ssl/cert.pem

# File with Diffie-Hellman parameters that the Postfix SMTP server
# should use with non-export EDH/DHE ciphers.
#
smtpd_tls_dh1024_param_file = /usr/local/etc/ssl/dhparam4096.pem

# The minimum TLS cipher grade that the Postfix SMTP server will use
# with opportunistic TLS encryption.
# Do not use weak encryption ciphers.
#
smtpd_tls_ciphers = high

# Enable EECDH key exchange for Forward Security
#
smtpd_tls_eecdh_grade = ultra

# The SMTP TLS security level for the Postfix SMTP server.
# Value "may" tells Postfix that it should use SSL/TLS if the remote
# host supports it, i.e., opportunistic TLS.
# There is a stricter option ("encrypt") to force Postfix to *always*
# encrypt, but that makes your server non-compliant with IETF RFC 2487.
#
smtpd_tls_security_level = may

# Enable additional Postfix SMTP server logging of TLS activity.
#   1 : log only a summary message on TLS handshake completion;
#       no logging of client certificate trust-chain verification
#       errors if client certificate verfication is not required.
# NOTE: do NOT use level 2 or higher except in case of problems.
#
smtpd_tls_loglevel = 1

# The SSL/TLS protocols accepted by the Postfix SMTP server with
# mandatory/opportunistic TLS encryption.
#
smtpd_tls_mandatory_protocols = !SSLv2, !SSLv3
smtpd_tls_protocols = !SSLv2, !SSLv3

# The minimum TLS cipher grade that the Postfix SMTP server will
# use with mandatory TLS encryption.
#
smtpd_tls_mandatory_ciphers = high

# Request that the Postfix SMTp server produces "Received:" message
# headers that include information about the protocol and cipher
# used, as well as the remote SMTP client CommonName and client
# certificate issuer CommonName.
# NOTE: This is disabled by default, as the information may be modified
#       in transit through other mail servers.  Only information that
#       was recorded by the *final destination* can be trusted.
#
smtpd_tls_received_header = yes

# Name of the file containing the optional Postfix SMTP server TLS
# session cache.  Specify a database type that supports enumeration,
# such as "btree" or "sdbm"; there is no need to support concurrent
# access.  The file is created if it does not exist.
#
smtpd_tls_session_cache_database = btree:$data_directory/smtpd_scache
#
# The expiration time of Postfix SMTP server TLS session cache
# information.  A cache cleanup is performed periodically every
# such time.
#
smtpd_tls_session_cache_timeout = 3600s


##
## Virtual domain hosting with Dovecot delivery
##

# Postfix virtual MAILBOX: separate domains, non-UNIX accounts,
# and non-Postfix mailbox store (use $virtual_transport).
#
# With the Postfix virtual(8) mailbox delivery agent, every recipient
# address can have its own virtual mailbox. virtual mailbox domains
# ($virtual_mailbox_domains) do not need the clumsy translation from
# each recipient addresses into a different address, and owners of a
# virtual mailbox address do not need to have a UNIX system account.
#

# Tell Postfix which domain(s) its virtual users live in.
# The specified domain(s) is also the final destination; mail is
# delivered via the $virtual_transport mail delivery transport.
#
# WARNING: NEVER list a "virtual_mailbox_domains" name as a
#          "mydestination" domain above!
#
virtual_mailbox_domains = $config_directory/virtual-domains

# Tell Postfix the virtual users for which its actually responsible
# for mail delivery.
#
virtual_mailbox_maps = hash:$config_directory/virtual-users

# Link alias e-mail addresses to real e-mail addresses.
#
# WARNING: NEVER put a virtual MAILBOX wild-card in the virtual
#          ALIAS file!!
#
virtual_alias_maps = hash:$config_directory/virtual

# With delivery to a non-Postfix mailbox store for hosted domains,
# the 'virtual_transport' parameter usually specifies the Postfix LMTP
# client, or the name of a "master.cf" entry that executes non-Postfix
# software via the 'pipe' delivery agent, which is responsible for the
# next-hop destination for final delivery to domains listed with
# $virtual_mailbox_domains .
#
# NOTE: Add the appropriate service definition in "master.cf" before
#       restart Postfix.
#
virtual_transport = dovecot
dovecot_destination_recipient_limit = 1


##
## Other settings
##

# Do not sends "new mail" notifications to users who have requested
# new mail notification with the UNIX command "biff y".
#
biff = no

# The maximal size of any 'local(8)' individual mailbox or maildir
# file, or zero (no limit).
mailbox_size_limit = 0
#
# The maximal size (byte) of a message, including envelope information.
message_size_limit = 52428800

# The default maximal number of parallel deliveries to the same
# destination.  This is the default limit for delivery via the 'lmtp(8)',
# 'pipe(8)', 'smtp(8)' and 'virtual(8)' delivery agents.
#
default_destination_concurrency_limit = 5

# The maximal number of parallel deliveries to the same destination
# via the relay message delivery transport.  This limit is enforced
# by the queue manager.
#
relay_destination_concurrency_limit = 1

# Disable the SMTP "VRFY" command, which is used to verify that an email
# address exists prior to sending a message, therefore stops some
# techniques used to harvest email addresses.
#
disable_vrfy_command = yes

# Require strictly RFC821 compliant envelopes, which requires that
# addresses received in "MAIL FROM" and "RCPT TO" commands are enclosed
# with <> and do not contain other comments or phrases, e.g.,
# <user@example.com>.
# This stops mail from poorly written software (may reduce spams).
#
strict_rfc821_envelopes = yes

# List or bit-mask of OpenSSL options to enable.
#
# * NO_COMPRESSION : disable SSL compression even if supported by
#                    the OpenSSL library.  Compression is CPU-intensive,
#                    and compression before encryption does not always
#                    improve security.
tls_ssl_options = NO_COMPRESSION

# The OpenSSL cipherlist for "high" grade ciphers.
#
# WARNING: you are strongly encouraged to NOT change this settings.
#
tls_high_cipherlist = EDH+CAMELLIA:EDH+aRSA:EECDH+aRSA+AESGCM:EECDH+aRSA+SHA256:EECDH:+CAMELLIA128:+AES128:+SSLv3:!aNULL:!eNULL:!LOW:!3DES:!MD5:!EXP:!PSK:!DSS:!RC4:!SEED:!IDEA:!ECDSA:kEDH:CAMELLIA128-SHA:AES12

# Log the hostname of a remote SMTP server that offers STARTTLS, when
# TLS is not already enabled for that server.
#
smtp_tls_note_starttls_offer = yes

# The minimum TLS cipher grade that the Postfix SMTP client will use
# with opportunistic TLS encryption.
# Do not use weak encryption ciphers.
#
smtp_tls_ciphers = high

# The default SMTP TLS security level for the Postfix SMTP client.
#   - may : opportunistic TLS.  Use TLS if this is supported by the
#           remote SMTP server, otherwise use plaintext.
#   - encrypt : mandatory TLS!
#
smtp_tls_security_level = may

# Enable additional Postfix SMTP client logging of TLS activity.
#
smtp_tls_loglevel = 1

# The SSL/TLS protocols accepted by the Postfix SMTP client with
# mandatory/opportunistic TLS encryption.
#
smtp_tls_mandatory_protocols = !SSLv2, !SSLv3
smtp_tls_protocols = !SSLv2, !SSLv3

# Name of the file containing the optional Postfix SMTP client TLS
# session cache.
#
smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache


##
## Mail filter (milter) settings
##

# The default action when a Milter (mail filter) application is
# unavailable or mis-configured.
#
milter_default_action = accept

# A list of Milter applications for new mail that arrives via the
# Postfix SMTP server.
#
# * inet:localhost:{{ mail.dkim.port }} - OpenDKIM
#
smtpd_milters = inet:localhost:{{ mail.dkim.port }}

# A list of Milter applications for new mail that does not arrive
# via the Postfix SMTP server.
#
non_smtpd_milters = $smtpd_milters


##
## Postscreen and additional filtering
##
## NOTE: Enable the corresponding daemons/utilities in "master.cf".
##

postscreen_access_list = permit_mynetworks

# Enforce non-spammy connection behavior (and not accept connections
# from clients that try to short-circuit the process to deliver
# spam faster).
#
postscreen_greet_action = enforce

# Enable DNS blacklist checking.
# DNSRBLs (DNS real-time black hole lists) are lists maintained
# by various entities, some companies, and some individuals, filled
# with IP addresses and ranges from which the list maintainer
# believes spam has originated.
#
postscreen_dnsbl_action = enforce
#
# Increase the DNS lookup timeout for the configured local recursive
# resolver by "unbound".
# Default: 10s
#
postscreen_dnsbl_timeout = 30s
#
# Lists:
# * zen.spamhaus.org
# * bl.spamcop.net
# * b.barracudacentral.org
#
# NOTE:
# The "b.barracudacentral.org" RBL requires registration!
# To test the access to this RBL:
#     $ host 2.0.0.127.b.barracudacentral.org
# If nothing returns, then access not granted to the used DNS, and
# registration is required.
# It seems that this RBL do not accept IPv6 address registration!
# See: http://www.barracudacentral.org/rbl/how-to-use
#
# Credit: https://serverfault.com/a/14256
#
# Useful tools:
# * Spam Database Lookup: http://www.dnsbl.info/
#
postscreen_dnsbl_sites =
	zen.spamhaus.org,
	bl.spamcop.net


##
## DEBUGGING CONTROL
##

# The debug_peer_level parameter specifies the increment in verbose
# logging level when an SMTP client or server host name or address
# matches a pattern in the debug_peer_list parameter.
#
debug_peer_level = 2

# The debugger_command specifies the external command that is executed
# when a Postfix daemon program is run with the -D option.
#
# Use "command .. & sleep 5" so that the debugger can attach before
# the process marches on. If you use an X-based debugger, be sure to
# set up your XAUTHORITY environment variable before starting Postfix.
#
# If you can't use X, use this to capture the call stack when a
# daemon crashes. The result is in a file in the configuration
# directory, and is named after the process name and the process ID.
#
debugger_command =
	PATH=/bin:/usr/bin:/usr/local/bin; export PATH; (echo cont;
	echo where) | gdb $daemon_directory/$process_name $process_id 2>&1
	>$config_directory/$process_name.$process_id.log & sleep 5

# vim: set ft=pfmain: